The leightweight scaffolding for more flexibility.

The MATO 2 system is unbeatable for round or angled building layouts. At the heart of the system are discs that are attached at a height of 50 cm and can be connected in four directions in a flash without tools. You benefit from labour savings of up to 50 %. Your competitors will be left in awe. The MATO 2 lightweight façade scaffolding is available in both steel and lightweight aluminium.

arrow Your advantages

  • Modularity: Connections in 4 spatial directions
  • Faster construction due to fast hanging of the railings and low weight
  • Great flexibility thanks to a wide range of accessories
  • Maximum safety EN 12810 / 12811
  • DIBt certification no. Z-8.1-967
  • Weight and handling advantages during transport and storage
  • System available as frame or post /transom scaffolding

Details

Modularity with a system.

The special construction features of the MATO 2 series are the result of many years of practical experience and targeted development work. The system is available as a frame or stem/bar scaffolding in widths of 95 or 65cm. The two design widths can be optionally combined.

The lightweight design was also consistently implemented for aluminium scaffolding coatings. This simplifies the installation and guarantees the user a maximum of safety.

Certain to be quicker and more flexible.

The MATO 2 lightweight scaffolding offers the scaffolder maximum flexibility. The heart of the system are the plates that are installed every 50cm up the scaffolding and enable connections in four directions.

In the case of round buildings or winding layouts, the MATO 2's strengths come to the fore and allow installation speeds of previously unknown dimensions. The installation of inserted floors, consoles and other accessories takes a matter of seconds and does not require any tools.

As strong as necessary, as light as possible!

MATO 2 is a contemporary lightweight system, which was developed specifically for more efficiency and flexibility for work on scaffolding. Depending on the construction height and maximum load, steel frames with a wall thickness of 2.7mm or aluminium frames with a thickness of 4mm are used. The steel design permits construction heights of up to 60m and higher, the aluminium version allows heights of up to 40m and higher.

For particularly strong loads, frames with a wall thickness of 3.25mm are available. They are compatible with the normal lightweight frames.

Time and cost savings of up to 50%.

Experience in practice has shown that with contemporary lightweight scaffoldings up to 50% of time savings can be achieved compared to traditional heavy systems. With consistently increasing cost pressure, this is an important factor for success. But the lightweight design not only has significant benefits when installing the scaffolding.

Thanks to the low weight, the load volume during transport is increased, handling becomes safer and storage is easier.

Your contact in Switzerland

Markus Etter

Markus Etter

Sales Manager Scaffolding
T: +41 (0)79 431 41 30
markus.etter@tobler-ag.com

Sascha Tischhauser

Sascha Tischhauser

Sales field service Scaffolding
SG, GR, TG, AR, AI, UR, GL, FL
T: +41 (0)79 395 69 14
sascha.tischhauser@tobler-ag.com

Markus Hübscher

Markus Hübscher

Sales field service Scaffolding
AG, BL, BS, SH, ZH, ZG, SZ
T: +41 (0)79 513 26 60
markus.huebscher@tobler-ag.com

Christian Mühlethaler

Christian Mühlethaler

Sales field service Scaffolding
BE, SO, LU, OW, NW, FR, VS
german
T: +41 (0)79 776 41 29
christian.muehlethaler@tobler-ag.com

Armando Martins

Armando Martins

Sales field service Scaffolding
VD, GE, JU, NE, FR, VS
French-speaking
T: +41 (0)79 795 10 37
armando.martins@tobler-ag.com

Salvatore Pasca

Salvatore Pasca

Sales field service
Scaffolding
TI
T: +41 (0)79 913 60 26
salvatore.pasca@tobler-ag.com

Field Service Abroad

Martin Tobler

Martin Tobler

CEO
T: +41 (0)71 886 06 20
martin.tobler@tobler-ag.com

Harald Herrndorf

Harald Herrndorf

Head of Sales Germany
T: +49 171 31 51 974
harald.herrndorf@tobler-ag.com

Michael Siebert

Michael Siebert

Area Sales Manager
Northern Germany, NRW, Niedersachsen, Hessen
(Rhein/ Main)
michael.siebert@tobler-ag.com

Mathias Müller

Mathias Müller

Area Sales Manager
Baden-Württemberg, Bayern PLZ: 80-87, 89
T: +49 151 705 839 72
mathias.mueller@tobler-ag.com

Adrian Lemmermeyer

Adrian Lemmermeyer

Sales field service
Scaffolding and Formwork
Vorarlberg & Tirol
T: +43 676 603 73 60
adrian.lemmermeyer@tobler-ag.com